Quality Plantation Shutters – How to Tell the Good From the Bad, Part 3 of 3

Plantation shutters can be purchased at almost every price imaginable. If you’re not a professional in the shutter industry, how do you distinguish between high-quality and low-quality products? There are a number of factors you can use to compare plantation shutters before making a commitment. In this article, we will explain how to tell the good from the bad.

Only wood plantation shutters will be discussed, since shutters made from MDF, composite, and polymer materials are different enough from wood plantation shutters in design and construction as to make fair comparisons impossible.

The Warranty Is The Best Proof of Quality

The truest measure of a company’s confidence in the products it offers is the strength of its warranty. Most manufacturers of plantation shutters offer coverage for at least 10 years; many go to 25 years. A few even offer lifetime warranties (lifetime is usually defined as the original purchaser owning the house the shutters were purchased for). Because plantation shutters are usually built to last for decades, and people today move for often than in the past, a couple of companies have begun offering warranties that are transferable to the next home-owner.

There are three things to look for in a warranty. The first is the term: the longer the better. Second, see what is covered, as some companies exclude the finish and other components. Finally, a warranty isn’t of much use if the company that backs it is not around when you need them. Make sure the company is well established so you can be confident they will be around for years to come.

Louver Shape Can Be A Factor

Louvers on traditional plantation shutters have an elliptical profile. They’re about 1/2″ thick in the middle and taper off at the edges. Some manufacturers make louvers with a flat profile because they are much easier to work with. A flat profile is quicker to paint, sand, and stain than an elliptical one, for example.

Flat louvers in and of themselves are not a quality flaw, especially when they are as substantial as their elliptical counterparts. However, many plantation shutters with flat louvers are made thin and insubstantial louvers, some are only 1/4″ thick. This is thinner than even the very tip of the louvers on a quality plantation shutter.

Thinner louvers are more likely to warp. Either stay with the traditional elliptical louvers, or, if you prefer flat louvers, make sure they are thick enough to last.

All Shutters Need Periodic Adjustment

Tension control is the balance between how easy it is to move the louvers and how well they stay in position once adjusted. After many years of use, you may find that the louvers on a plantation shutter have loosened; the solution is to tighten the tension, if you can. Traditionally, manufacturers provide a screw in one or more of the louvers to adjust the tension. You tighten the screw to increase tension; loosen it to decrease tension.

Some manufacturers install self-tensioning nylon pins. Once installed, these pins cannot be adjusted. Although they are marketed as never needing maintenance, shutters with these pins actually need their tensioning adjusted about as often as shutters without them.

Manufacturers that omit tension screws are doing so for one reason: to reduce their costs. Make sure the shutters you purchase are designed to provide decades of service by giving you a way to tighten louvers as needed.

Beware of Plastic Staples on the Tilt-Rod

A tilt-rod is the vertical piece of wood running down the middle of each shutter panel that attaches to each louver. You use a tilt-rod to adjust the angle of the louvers.

Traditionally, tilt-rods are connected to the louvers by metal staples. Over time, or in a household with heavy use (such as one with small children), it’s possible for the staples to be pulled out. Metal staples are easily repaired or replaced by pushing the staple back into its hole. To help secure it in place, a drop of glue can be put into the hole first and the excess wiped off. If you lose the staple, replacements are available at almost any hardware store, and most manufacturers will send replacements for free.

However, some manufacturers have switched to using plastic staples instead of metal ones. Not only are the plastic staples more complicated and fragile than their metal counterparts, it is almost impossible to find either the parts themselves or someone to fix your shutter if they are damaged.

Buy A Quality Shutter…But Don’t Buy More Than You Need

There are literally thousands of shutters on the market today. Most of them display a mix of high-quality and lesser-quality characteristics. Buying quality is important; but buying more shutter than you need is a waste of money. Hopefully you are now armed with the information to shop knowledgeably for the quality shutters you need and want for your home and lifestyle.

Buy Office 2019 Professional Plus Here for 9.99$ : https://ndwsmarket.com/product/microsoft-office-2019-professional-plus-for-windows-pc/

How much does Office 2019 cost?

See more on : NDWSmarket.com


Source by Nathan Newton

SHOPPING CART

close